In recent years, with the country’s strong support for the environmental protection industry and the development of the solar street light industry, solar street lights have become more and more popular. How to use solar street lights correctly is very important. Correct installation before use is a part, and correct maintenance after use is also Part of it, today the source code solar street light editor summarizes some common faults and solutions for solar street lights, hoping to help you do a better job in the daily maintenance of solar street lights.
1. The following items need to be paid attention to in daily use of solar panels:
(1) Do not let hard or sharp objects hit the solar panel, otherwise it will damage the solar panel.
(2) Solar panels should be cleaned regularly during use (the time can be once a quarter or half a year). Keep the surface of the solar panel clean, otherwise it will affect the conversion efficiency.
(3) Do not let some things (such as branches, billboards, etc.) block the surface during use, otherwise it will affect the conversion efficiency.
(4) The orientation and angle of solar energy installation.
2. LED solar street lights are dark and the street lights are not on. Common faults and troubleshooting are as follows:
(1) If you have just unpacked and the test lamp does not light up, first check the response of the indicator light of the controller;
a. Please check whether the solar panel wire and the lamp head wire are well connected and tightened.
b. When the solar panel cable is connected, the battery indicator light (red light) of the controller will always be on. If it is not on, the battery may be out of power. Put the lamp head and the solar panel under the sun at the same time, and observe the indicator light of the controller Status, such as the red light is always on, the blue light flashes slowly, and the lamp is normal; if the status of the indicator lights is not on, please consult the manufacturer’s engineer for guidance.
c. The indicator light is flashing normally, and it does not light up when the remote control is in demo mode. Please pay attention to observe whether the three indicator lights of the controller flash at the same time when pressing the remote control to send. If they do not flash at the same time, it means that the remote control has not sent successfully. , adjust the remote control distance, and send again. If the transmission is still unsuccessful, the remote control may be broken, or the battery of the remote control is dead. Please try another remote control.
d. If you test in daytime, press the demo mode of the remote control to still not turn on the light, but the three indicator lights of the controller have flashed three times at the same time, indicating that the controller has been successfully received. Please check whether the solar panel has been buckled, and use a shading object to Cover the solar panels completely.
3. The source code LED solar street light does not light up in the dark (compared to other lighting time later), common faults and troubleshooting are as follows:
If the source code solar street light has been installed and has not been used yet, the street light does not light up at night (exclude the line failure problem)
Reason: It is not a street light failure, because the quality of the solar panel is very good, the photoelectric conversion rate is high, and the light will not turn on if it does not reach the light control voltage point. When the voltage is lower than the light control voltage point and the solar panel is not in the power generation state, the light is on.
Solution: If you want to turn on the light earlier, you can use the remote control to set the light control voltage point, and set the light control voltage to a higher level, then the lighting time of the lamp will be relatively earlier.
4. LED solar street lights are dark and the street lights are not on. Common faults and troubleshooting are as follows:
(1) If it has been installed and used normally for a period of time, first check the response of the indicator light of the controller;
a. All indicator lights are off, the battery may be over-discharged, and the battery hardware is protected. You can check the status of the indicator lights during the next day. If the red light is always on and the blue light is flashing, it means that the light is charging normally, and the light is normal; if the second If the status of the indicator light is not on every day, you need to contact the manufacturer’s engineer to further analyze the reason.
b. The light is normally on for a period of time, but the lighting time is short. Please observe the surrounding environment, whether the solar panel is blocked, the installation angle of the solar panel, whether to adjust the angle of the maximum irradiated area of the road, and whether it has been continuously for several days recently. It is a rainy day, if none of the above problems exist, please use the universal remote control to read the setting parameters, whether it is the normal factory mode setting, the current setting may be too high or the control factory mode is changed, resulting in short lighting time, if this is the case, please call back Factory default mode.
Post time: Feb-22-2023